Concrete cutting in Newton MA - clean, straight openings right where you need them
Need a doorway, a trench line or a pipe hole through existing concrete? We scan first, then cut it straight and clean.
- Fully licensed and insured.
- Free in-person estimates.
- We respond within 1 business day.
Can you cut an opening into concrete that's already poured?
Concrete cutting in Newton means opening up concrete that has already hardened. We use diamond saws and core bits to cut straight lines, trench lines or round holes for a pipe, so you can take out one bad section or run a new line without breaking up the whole slab.
Usually the concrete itself is fine, and you just need part of it gone or a way through it. The price moves with how thick the concrete is, how much steel is inside, whether you need a straight cut or a round hole, how easy the spot is to reach and whether you want the pieces hauled away. The schedule depends on the scan, any permit the job needs and the hours the city allows for noisy work. We're based in Newton and work here and in the cities around it. Your written estimate spells out the prep, the cleanup and who handles any permits, so you know what you're paying for before we start.
When does it make sense to cut concrete instead of tearing it out?
One sunken driveway panel
One section has dropped or broken up while the panels around it still sit flat. That usually means the ground gave way under that one section, so a clean cut lets us take out just that piece. If you wait, water runs under the edges and loosens the panels next to it.
A pipe has to cross the floor
Your plumber needs a drain under the basement or garage slab, or an electrician needs a path for conduit. A saw cut or a cored hole keeps the opening only as big as it needs to be. Chipping at the slab with a hammer usually leaves a ragged hole and a much bigger patch.
A new door in the foundation
You want a doorway, a window or a bulkhead opening through a poured foundation wall. That wall holds up part of the house, so the opening gets planned on paper before anyone marks it. Putting it off usually means the rest of the remodel waits on it.
How we handle concrete cutting, start to finish
First I look at the spot and ask what the opening is for, because a drain line and a doorway call for different saws and different care. Then we scan the concrete before we mark a single cut, looking for rebar, the steel bars that hold a slab together, and anything else running through it. We snap the lines, set up the saw that fits the job, cover the floors and walls around the work, and cut. If your job includes removal, we break out the cut pieces, haul them away and leave a clean edge ready for whatever comes next.
A cut is often the start of new work. When a driveway panel comes out, we can pour the replacement through our concrete driveway building work, and a cracked or sunken patio can come out in sections ahead of new concrete patio construction. On those jobs I'd rather spend your money on the base than on a fancier surface. The base is the dug-out, packed ground under the slab. Nobody sees it on day one, but it decides whether the new concrete settles like the old.
Flat sawing for slabs
This walk-behind saw makes straight cuts in driveways, patios, garage floors and basement slabs. It's the right choice for taking out a panel or cutting a trench line for a pipe.
Wall sawing on a track
For vertical concrete like a foundation wall, the saw rides on a track bolted to the wall so the cut stays straight. It's the right choice for doorways, windows and other openings through a wall.
Core drilling for round holes
A round hole for a pipe, a drain or a conduit usually goes to a core bit rather than a saw. That's why holes and saw cuts are priced differently on your estimate.
Hand sawing in tight spots
When there's no room for a bigger saw, such as near a wall, in a corner or beside a set of steps, a hand saw reaches in. It's slower work, but it lets us cut close without disturbing what's around it.
Get a written price for your concrete cut
Send the form and we'll reply within one business day to set a time. I'll come out and look at the cut with you, then you get a free written estimate, with no pressure and no obligation.
Call (617) 644-7325What happens after you call about concrete cutting in Newton?
From your first call to the final walk-through, here's who you'll deal with and what you'll have in hand at each stage.
Call or send the form
Tell us where the cut goes, whether it's in a slab or a wall or is a round hole, and whether you want the pieces hauled away. Then we set a time for me to come see it.
Walk the spot with me
I come out, ask how you use the space and talk you through your choices right there. Your written estimate spells out the prep, the cleanup, who handles any permits and whether we only saw the lines or also break and haul the pieces, so you can see where the money goes.
Scan, mark and cut
We scan and cut during the city's construction noise hours, which generally run 7 AM to 7 PM Monday to Friday and 8 AM to 7 PM on Saturday. Before the saw starts, we cover the floors, walls and plantings around the cut.
Clean up and walk through
We clean up and haul away whatever your estimate says we will, and then I walk the finished cut with you. I'll show you how to care for the new edge or opening and what to keep an eye on.
Why Newton homeowners call Excel Newton Concrete for cutting
On a cutting job, the careful part is everything that happens before the saw starts, like the scan and the marks on the slab. Tell me about the spot through our contact page or call (617) 644-7325, and I'll come out and walk it with you.
I plan it and I'm there
I come out to look at your job myself, and my crew does the cutting with me on site. The person who walked the spot with you is the one standing there when the blade goes in.
Nine years of slabs and foundations
We've been in business since 2017. Before we started working on homes where families live, I learned the trade pouring foundations and slabs on new construction, and knowing how a slab gets built helps when you're the one cutting into it.
Licensed, insured and held to state rules
We're fully licensed and insured. Massachusetts requires a licensed construction supervisor or a registered design professional to oversee construction on one- and two-family homes, with an exemption for homeowners, and any contractor working on an existing owner-occupied home with one to four units must be registered as a Home Improvement Contractor.
Written estimates you can compare
Our estimates are written out so you can line them up against other quotes, and Massachusetts law requires home improvement contracts over $1,000 to be in writing anyway. Seeing every step on paper is how you spot the shortcut in a cheaper quote.
Cutting, patching and new slabs at Newton homes
Newton's Inspectional Services Department issues permits for building, altering, repairing and demolishing buildings and structures. It's the office to ask whether your cut needs a permit, and I won't guess at that for a wall opening or a floor trench. When a job needs a permit, we pull it in our name and set up the inspections. If we aren't sure, we check with the city before we start.
Questions about concrete cutting in Newton
How much does concrete cutting cost in Newton?
Saw cutting of slabs and walls usually runs about $4 to $25 per linear foot across the US, and that national figure covers the sawing alone, not removal. Thicker or reinforced concrete costs more per foot, round holes are priced differently from saw cuts, and small jobs often carry a minimum charge or a set fee for coming out. Breaking, hauling and disposal can cost more than the sawing itself, so check whether each quote includes removal before you compare them.
Why scan concrete before cutting it?
Scanning shows where the rebar, tensioned cables and live conduit are before anyone marks a line. Tensioned cables are steel cables pulled tight inside some slabs, and cutting one or cutting into live conduit can be deadly. A scan lowers that risk but doesn't prove a spot is completely clear, and I'll tell you that plainly before we cut.
Will cutting out a section of my driveway crack the rest of it?
A clean saw cut usually leaves the rest of the driveway alone, because the blade separates the bad panel along a straight line instead of shaking it loose with a hammer. We cut all the way through so the panel lifts out without prying on its neighbors, and the straight edge gives the new pour a clean line to meet.
What is the best way to keep dust down when cutting concrete?
Keeping water on the saw blade is the best way, because wet cutting creates much less dust than dry cutting. The trade-off is slurry, the gray mix of water and fine concrete, which can run farther than you'd expect and reach finished rooms. Ask any crew how they'll catch it. The cleanup section of our written estimate covers how we will.
How do I know if I need an engineer to cut an opening in a foundation wall?
If the wall holds up part of the house, and a foundation wall usually does, an engineer takes part before anyone cuts the opening. A cutting field guide puts the engineer in charge of any structural opening. That's a normal planning step, not a sign that something is wrong with your house.
Can concrete cutting be done on a Sunday in Newton?
In general, Newton allows construction noise on Sundays and holidays only with a permit the Mayor approves. For work that falls outside the city's noise ordinance, you can ask for an exemption through the city's noise ordinance waiver request. We'll plan the dates with you before we book the saw.
Concrete work that often follows a cut
- Concrete driveway building
When a cut panel comes out, the new section needs a dug-out, packed base and a proper pour so it sits level with the driveway around it.
- Concrete patio construction
If you're cutting out a sunken or cracked patio, we can rebuild it with a slope that carries water away from your house, not toward it.
Newton, MA
Tell us where your cut needs to go
We answer the phone until 9 PM every day, so you can call (617) 644-7325 after work and describe the spot while you're standing next to it.